Nmap using TOR

Got a good video about how to do a scanning using nmap and TOR. It increases the anonymity factor.

For further reference, refer here. Also this could be useful.

Nullcon Capture The Flag 2010 hacking competition : How did I crack it

Recently I had been to Nullcon, Goa, 2010 - Internation Hacking and Security Conference.Well a lot to say. It was a great experience. My first hacking experience, unforgettable. Here is the details:

Goal : There was a server, we had to shut it down.

Hint: "Its there in the air"

Step 1: I found the wireless network they have configured for the challenge. Definitely the server is inside that network. It was WEP encrypted network. I used aircrack-ng in Backtrack 4. Steps are explained here. Better explanation could be helpful. Still confused!!! then watch this:

Step 2: Once I got the key and connected the network, I started looking for the server. Now here they had configured two network one with 192 series ip that I was connected to and another one with 172 series ip where the server is. Also they have configured the firewall in the router so that no packets could reach to 172 network. So first firwall had to be disabled. But root priviledge was required to do so. So task is, gain root access to the router 192.68.1.1.

fingerprinting using nmap (nmap -O ip) gave the firmware details of the router: it was dd-wrt firmware. Searched for the existing vulnerabilities or exploits for that and foung cgi-bin vulnerability. It could be exploited by command-line approach or using metasploit. I found metasploit easier and faster as well. Once done successfully, I got the root shell in the router.

Step 3: Now disable the firewall.

They had set up iptable rules to drop the packet. So here are the commands:

iptables -L -nv

It showed the configured rule to drop all the packets mentioned earlier.

Now,

iptables -P FORWARD ACCEPT

iptables -F FORWARD

It allowed the connections through. If you want to allow only traffic from your machine then,

iptables -I FORWARD -p all -d -j ACCEPT

Once this is done. I was able to reach the server which was 172.16.1.2 (I guess).

Step 4: Now I could ping the server. Now I had to get into the server. So did a port scanning on that machine

nmap -sS -PT 172.16.1.2 (requires root privilege)

Found port 445 was open. It was SMB over TCP. Already an exploit was available in metasploit. So just ran that and BINGO... I got the command promt of the server.

Step 5: Shoutdown the server. Since I was already inside the server. Only thing required was to run the following:

SHUTDOWN -s -t 01

And I was done...

Spoof Mac in Mac

A MAC address is a unique identifier assigned to your network card, and some networks implement MAC address filtering as a method of security. Spoofing a MAC address can be desired for multiple reasons, and it is very easy to spoof your MAC address in both Mac OS X 10.4 and 10.5. For the purpose of this article, we are going to assume you want to spoof your Mac’s wireless MAC address. So without further ado, here’s a 3 step process on how to do it:

Retrieving your current MAC address

First, you’re going to want your current wireless MAC address so you can set it back without rebooting. Launch the Terminal and type the following command:
ifconfig en1 | grep ether
You’ll know see something like:
ether 00:12:cb:c6:24:e2
And the values after ‘ether’ makeup your current MAC address. Write this down somewhere so you don’t forget it. If you do, it’s not the end of the world, you’ll just have to reboot to reset it from a change.

Spoofing a MAC address

To spoof your MAC address, you simply set that value returned from ifconfig to another hex value in the format of aa:bb:cc:dd:ee:ff

For this example, we will set our wireless MAC address to 00:e2:e3:e4:e5:e6 by issuing the following command:
sudo ifconfig en1 ether 00:e2:e3:e4:e5:e6

The sudo command will require that you enter your root password to make the change.

Verifying the Spoofed MAC address worked

If you want to check that the spoof worked, type the same command as earlier:
ifconfig en1 | grep ether
Now you will see:
ether 00:e2:e3:e4:e5:e6
Meaning your MAC address is now the value you set it to. If you want to further verify the spoof, simply login to your wireless router and look at the ‘available devices’ (or attached devices) list, and your spoofed MAC address will be part of that list.

If you want to set your MAC address back to its real value, simply issue the above ifconfig commands with the MAC address that you retrieved in step 1. You can also reboot your Mac.

Enjoy!

Note: Reader Dee Brown points out the following, which may help with some users having difficulties: “running 10.5.6 you need to do the trick to disassociate from the network. ****DO NOT TURN AIRPORT OFF****. What you will have to do is click your airport and click join network and enter some bogus name as the network ssid. Then while it’s trying to connect click cancel.At this point you may spoof using the sudo ifconfig en1 ether command”

other reads point out that Dee Brown’s trick works in 10.5.7 and above too. Thanks Dee!

Update: If you’re still having problems with MAC address spoofing in Leopard or Snow Leopard, the above method still works but try disassociating with any wireless network BUT keep your wireless Airport on (as mentioned above) – an easy way to do this is to type the following in the command line:

airport -z

Note that you have to have the ‘airport’ command setup to work for users, you can do that by copy and pasting this command into the Mac Terminal:

sudo ln -s /System/Library/PrivateFrameworks/Apple80211.framework/Versions/Current/Resources/airport /usr/sbin/airport

Once disassociated from the network you should be able to spoof your MAC address as usual

[Copied from http://osxdaily.com/2008/01/17/how-to-spoof-your-mac-address-in-mac-os-x/]